Sinks and plumbing
Kitchen Faucet Guide: Types, Spout Reach and Installation
The kitchen faucet is used dozens of times a day. Choosing one involves the style of sprayer, the size of the spout in relation to the sink, the number of mounting holes, and the quality of the valve inside.
This guide explains those choices and the usual installation requirements. Dimensions differ between models, so compare the specification sheet with the sink and the space behind it. Replacing a faucet on existing shutoff valves is a common homeowner task. Changes to supply piping are normally work for a licensed plumber.
Faucet types
- Pull-down: a high arched spout with a spray head that pulls straight down into the sink. It suits deep single-bowl sinks and is the most common type in new kitchens.
- Pull-out: a lower spout with a spray head that pulls out toward the user. It suits shallow sinks, double bowls and locations with limited height, such as under a low window sill or shelf.
- Standard spout with side sprayer: a fixed spout and a separate hand sprayer mounted in its own hole.
- Bridge: hot and cold handles joined to the spout by an exposed horizontal pipe above the counter. It needs two or three holes and suits traditional kitchens.
- Commercial or pre-rinse style: a tall spring-supported spray hose. It needs generous height and a large sink to contain the spray.
- Wall-mount: the faucet is installed through the wall above the sink. The supply piping and valve are inside the wall, so the location has to be set during rough plumbing.
- Pot filler: a cold-water faucet on a folding arm mounted near the range. It requires a supply line in that wall and has no drain below it.
Handle arrangement is a separate choice. A single handle controls flow and temperature with one hand and needs one hole. Two handles give separate hot and cold control and need more holes.
Spout height and reach
Two dimensions decide whether a faucet suits a sink. Spout height is the vertical clearance under the spout. Spout reach is the horizontal distance from the center of the faucet base to the center of the water stream.
| Dimension | Typical range | What to check |
|---|---|---|
| Spout reach | 8 to 10 inches | The stream should land near the center of the bowl, at or close to the drain |
| Spout height, high arc | 8 to 10 inches of clearance, with 15 to 22 inches overall height | Clearance under wall cabinets, shelves and window sills |
| Spout height, low arc | 3 to 8 inches of clearance | Room to fit large pots under the spout |
| Hose length on pull-down and pull-out models | About 20 to 30 inches of extension | Reach to all corners of the sink |
| Space behind the faucet | About 2 to 3 inches to the backsplash | Room for the handle to move through its full range |
A tall faucet over a shallow sink splashes. A short reach over a large sink puts the stream at the back wall of the bowl. With a double-bowl sink, the spout needs to swivel far enough to serve both bowls. A handle mounted on the side or front of the faucet body avoids the problem of a rear-tilting handle hitting the backsplash.
Mounting holes and deck plates
Faucets are made for one, two, three or four holes. The standard hole diameter is about 1 3/8 inches. In a three-hole sink, the outer holes are typically 8 inches apart, measured center to center.
A single-hole faucet can be installed on a three-hole sink by using a deck plate, also called an escutcheon, that covers the unused holes. The reverse is not possible without drilling. With an undermount sink the holes are drilled in the countertop by the fabricator, so the faucet and accessories must be chosen before fabrication. Stone and quartz cannot be drilled casually later.
Check the thickness of the mounting surface. Most faucets accept a deck up to about 1.5 to 2.5 inches thick. A thick countertop may need an extension kit from the manufacturer.
Valves, materials and finishes
The valve controls the water and is the part that wears. Ceramic disc valves are the current standard. They resist wear and mineral buildup, and they rarely drip. Older compression valves with rubber washers need more frequent repair.
Faucet bodies are commonly made of brass or stainless steel, with zinc alloys and plastic used in lower-priced models. Products that carry drinking water must meet federal lead-free requirements, and certified products are marked as meeting the relevant NSF/ANSI standards.
- Chrome: durable and inexpensive, shows water spots
- Stainless or brushed nickel: hides fingerprints and spots better than polished finishes
- Matte black: shows mineral deposits in hard-water areas and needs gentle cleaners
- Physical vapor deposition (PVD) finishes: a hard coating that resists scratching and tarnish better than standard plating
Flow rate and water pressure
The federal maximum flow rate for kitchen faucets is 2.2 gallons per minute. Many current models are rated at 1.5 or 1.8 gallons per minute, and some states, including California, set a lower limit than the federal one. Lower flow saves water and makes filling a large pot slower. Some faucets have a temporary boost setting for filling.
Installation requirements
- Shutoff valves on the hot and cold supplies under the sink. Old or seized valves are worth replacing at the same time.
- Flexible supply lines of the right length and connector size, commonly 3/8-inch compression at the valve
- Clear space under the sink for the pull-down hose and its weight to travel without catching on the disposal, trap or stored items
- An outlet or battery pack for touch or motion-activated models
- A separate small faucet and line if a water filter or instant hot water dispenser is being added
- Sealant or a gasket at the base, as the manufacturer specifies
Common faucet selection mistakes
- A high-arc faucet that does not fit under a cabinet, shelf or window sill
- A handle that hits the backsplash before reaching full hot
- A spout that does not reach the center of the sink
- Choosing the faucet after the countertop has been drilled
- A tall, powerful sprayer paired with a shallow sink
- Forgetting holes for a soap dispenser, filter faucet or air gap
- Selecting a finish that cannot be matched in other fixtures and hardware
- Storing items under the sink where they block the pull-down hose
Frequently asked questions
What is the difference between a pull-down and a pull-out faucet?
A pull-down faucet has a tall spout and a spray head that pulls downward into the sink. A pull-out faucet has a shorter spout and a head that pulls toward the user. Pull-down models suit deep sinks, and pull-out models suit shallow sinks or limited overhead space.
How far should a kitchen faucet reach?
The water stream should land near the center of the bowl. For most sinks that means a spout reach of about 8 to 10 inches, measured from the center of the faucet base.
Can a single-hole faucet be installed on a three-hole sink?
Yes. A deck plate supplied with the faucet, or sold separately, covers the two unused holes. Check that the plate is long enough to cover an 8-inch hole spacing.
What is a ceramic disc valve?
It is a valve in which two polished ceramic discs slide against each other to control flow. Ceramic disc valves last longer and drip less than washer-based valves and are used in most current kitchen faucets.
Is a plumber needed to replace a kitchen faucet?
Not always. Replacing a faucet on existing, working shutoff valves is a common do-it-yourself job with basic tools. A plumber is advisable if the shutoff valves are corroded, the supply piping needs to change, or a wall-mount faucet or pot filler is being added.