Countertops
Butcher Block Countertops: Wood Types, Finishes and Care
Butcher block is a countertop made from strips of hardwood glued together. It costs less than most stone, can be cut and installed with woodworking tools, and can be sanded and refinished when it wears. It also needs more routine care than other countertop materials, especially near water.
This guide covers how butcher block is constructed, the common species and sizes, the two main finishing approaches, and how to install and maintain it. Finish products differ, so follow the label for application, cure time and food-contact suitability.
Edge grain, end grain and face grain
- Edge grain: long strips glued with their narrow edges facing up. This is the standard countertop construction. It is stable, economical and shows long parallel lines.
- End grain: short blocks arranged so the ends of the wood fibers face up, giving a checkerboard look. It is the most forgiving surface for knives and the most expensive. It absorbs more finish and more water.
- Face grain or plank style: wider boards glued with their broad faces up. It shows the most grain pattern but dents and scratches more easily and is more prone to cupping.
Most kitchen countertops sold as butcher block are edge grain. End grain is often limited to an island or a dedicated cutting section.
Common wood species
| Species | Characteristics | Relative cost |
|---|---|---|
| Hard maple | Hard, fine closed grain, light color. The traditional butcher block wood. | Moderate |
| Birch | Slightly softer than maple, light color with some variation | Low |
| Beech | Hard, fine grain, pale pinkish tone | Low to moderate |
| Red or white oak | Hard with open, prominent grain. White oak resists moisture better than red oak. | Moderate |
| Walnut | Medium hardness, dark brown, dents more easily than maple | High |
| Cherry | Medium hardness, darkens to reddish brown with light exposure | Moderate to high |
| Acacia and rubberwood (hevea) | Imported hardwoods with varied color, common in budget tops | Low |
Closed-grain woods such as maple and beech are easier to keep clean on a surface used for food preparation. Open-grain woods such as oak hold more residue in their pores unless the grain is filled or sealed with a film finish.
Standard sizes and thickness
- Thickness: 1.5 inches is standard. Tops of 1.75 to 2.25 inches are common for islands, and end grain blocks can be 3 inches or more.
- Depth: 25 inches for standard counter runs. Island tops are commonly 30, 36 or 42 inches deep.
- Length: stock tops are usually sold in lengths from 4 to 12 feet and cut to fit.
- Weight: a 1.5-inch maple top weighs about 5 to 6 pounds per square foot, much less than stone.
Because the material is cut on site, corners are usually joined with a butt joint or a miter, pulled tight with countertop connector bolts from below. Long runs can be joined the same way.
Oil finish compared with film finish
There are two approaches to finishing, and the choice determines how the countertop is used and maintained.
A penetrating oil finish, such as food-grade mineral oil, often combined with beeswax, soaks into the wood and leaves no surface film. The top can be used for direct food preparation, and scratches or stains can be sanded out and re-oiled in a few minutes. The oil does not make the surface waterproof and it wears away. A new top typically needs several coats in the first weeks, then re-oiling about once a month or whenever the wood looks dry.
A film-forming finish, such as polyurethane, a conversion varnish or a hardwax oil with a hardening component, builds a protective layer. It resists water and stains far better and needs little routine care. It should not be cut on, because knife cuts break the film and let water under it. Repairs usually mean sanding and recoating a whole section. Film finishes need their full cure time, often several weeks, before heavy use.
A common arrangement is a film finish on tops near the sink and an oil finish on an island used for prep. All faces, including the underside and cut edges, should be finished so the wood takes up and releases moisture evenly.
Installation and wood movement
Wood expands and contracts across its width as indoor humidity changes through the year. A 25-inch-deep top can move by roughly 1/8 inch or more between seasons. Installation has to allow for this.
- Let the top acclimate in the house for several days before cutting and fastening.
- Fasten from below through oversized or slotted holes with washers so the top can move. Do not glue it to the cabinets.
- Leave a gap of about 1/8 inch at walls, covered by the backsplash or a bead of flexible sealant.
- Seal sink and faucet cutouts thoroughly on all cut surfaces before installing the fixtures.
- Keep the required clearance or protection next to a range, following the range manufacturer's instructions for combustible surfaces.
- Provide support for overhangs. Roughly 8 to 12 inches unsupported is typical, depending on thickness and grain direction.
Daily care and repair
Wipe up water promptly, especially around the faucet and at the dishwasher, where steam and drips are frequent. Clean with a damp cloth and mild soap, and do not leave wet cloths, sponges or standing water on the surface. Use trivets, since hot pans can scorch wood.
On an oiled top, light stains and scratches come out with fine sandpaper followed by fresh oil. Dark stains around a sink usually indicate that water has penetrated, and they need deeper sanding and resealing. On a film-finished top, watch for worn or cracked areas and recoat them before water gets beneath the finish.
Common butcher block mistakes
- Finishing only the top face, which leads to cupping
- Gluing or screwing the top down tightly so it cannot move, which leads to cracks
- Using a cooking oil such as olive or vegetable oil, which can turn rancid. Food-grade mineral oil is the usual choice.
- Installing an undermount sink without sealing the cutout edge thoroughly
- Cutting directly on a film finish
- Skipping the monthly oiling on an oil-finished top
- Leaving the top unfinished for weeks after delivery
- Using stain under an oil finish on a surface meant for food preparation without checking that the products are suitable
Frequently asked questions
Can butcher block be used around a sink?
Yes, with care. The sink cutout and faucet holes must be fully sealed, and a water-resistant film finish is the safer choice in that area. Water left standing at the sink edge is the most common cause of staining and decay in wood countertops.
How often does butcher block need to be oiled?
A new oil-finished top usually needs several applications in its first month. After that, about once a month is typical, or whenever the surface looks dry or water stops beading. Tops with a film finish do not need oiling.
Is butcher block sanitary for food preparation?
A well-maintained hardwood surface is suitable for food preparation when it is washed with soap and water and allowed to dry. Many households still use a separate cutting board for raw meat so it can be washed thoroughly in the sink.
How long do butcher block countertops last?
With regular maintenance and protection from standing water, a wood countertop can last 20 years or more, and it can be sanded and refinished several times. Neglected tops near sinks can fail much sooner.