KITCHEN MASTERS

Lighting and electrical

Under-Cabinet Lighting: Types, Placement and Wiring

Updated November 19, 2026

Under-cabinet lights are mounted on the bottom of wall cabinets to light the countertop. They are the most direct form of task lighting in a kitchen because the light source is between the cabinets and the work surface, where ceiling lights cannot reach.

This guide compares the fixture types, gives typical brightness and placement guidelines, and explains the power and control options. Hardwired lighting must follow the local electrical code and is normally installed by a licensed electrician under a permit. Low-voltage and plug-in products should be listed by a recognized testing laboratory and installed according to their instructions.

Types of under-cabinet lights

TypeDescriptionTypical use
LED tape or stripA thin flexible strip of LEDs, usually 12 or 24 volts, cut to length and powered by a driver. Often mounted in an aluminum channel with a diffuser.Continuous, even light along the full run. The most flexible option for new kitchens.
LED light barA rigid fixture in fixed lengths, commonly 8 to 48 inches, that can be linked end to end. Available in low-voltage and 120-volt versions.Simple installation in new or existing kitchens.
Puck lightsSmall round fixtures spaced along the cabinet bottom.Pools of light for accent or display. Less even for task lighting.
Battery or rechargeable unitsSelf-contained lights fixed with adhesive or magnets.Rentals and locations with no power. Lower output and regular recharging.

LED has replaced fluorescent and xenon fixtures in almost all new work. It runs cooler, uses less power and fits in a much thinner profile.

Brightness and light quality

  • Output: about 200 to 500 lumens per linear foot is typical for task lighting. The lower end suits light countertops, and the higher end suits dark or matte surfaces.
  • Color temperature: match the room's other lights. 2700K to 3000K is warm white and 3500K to 4000K is neutral.
  • Color rendering: a CRI of 90 or higher makes food and finishes look more natural.
  • Dimming: a dimmable system allows full output for prep and a low level for evening or night lighting.
  • Diffusion: a frosted lens or a deep channel blends the individual LED points into a continuous line.

Polished stone and other glossy countertops reflect the individual LEDs of a bare strip as a row of bright dots. A diffuser, a strip with closely spaced LEDs, or mounting the strip so it faces the backsplash at an angle reduces this effect.

Mounting position under the cabinet

The usual position is toward the front of the cabinet bottom, just behind the face frame or front edge. From there the light spreads across the full depth of the counter and reaches the area where most work happens. Mounting at the back, against the wall, lights the backsplash brightly and leaves the front of the counter dimmer.

The fixture should not be visible from a normal standing or seated position. Framed cabinets usually have a recess under the bottom panel that hides a slim fixture. Frameless cabinets have flat bottoms, so a light rail molding about 1 to 2 inches high is commonly added at the front edge, or a channel is recessed into the cabinet bottom during manufacture.

Run the lights the full length of each cabinet section so there are no dark gaps. Where cabinets are interrupted by a window, range hood or open shelf, each section is fed separately, and the connecting wires are routed through the cabinets or the wall.

Power options: hardwired, low-voltage and plug-in

A hardwired 120-volt system connects each fixture to building wiring, controlled by a wall switch or dimmer. It is the cleanest result and is easiest to install during a remodel when the walls are open.

A low-voltage system uses a driver, also called a transformer or power supply, to convert 120 volts to 12 or 24 volts. The driver must be installed in an accessible, ventilated location, such as inside a cabinet, above the cabinets or in a basement below. It must not be sealed inside a wall. The driver's wattage rating needs to exceed the total load of the strips, commonly with a margin of about 20 percent. Long runs of low-voltage strip lose brightness toward the far end, which is why 24-volt systems are preferred for longer runs.

A plug-in system connects to a countertop receptacle or to an outlet placed inside or above a cabinet. It is the simplest retrofit. The visible cord can be reduced by adding a switched outlet inside the wall cabinet, which is work for an electrician.

Planning the wiring during a remodel

  1. Choose the lighting system before the electrical rough-in so the electrician knows whether to run 120-volt cable to each cabinet section or low-voltage wire from a central driver.
  2. Mark the exact height of the bottom of the wall cabinets on the studs. The wire should exit the wall just below that line so the cabinet hides it.
  3. Decide on the switch location and the type of dimmer. Low-voltage systems need a dimmer that is compatible with the driver.
  4. Plan the driver location with access for future replacement.
  5. After cabinets are installed, mount the fixtures, conceal the connecting wires with clips or wire channel, and test before the backsplash is completed.

Wire that exits the wall in the middle of the backsplash area is hard to hide after tile is installed, so the exit height is the detail most worth checking on site.

Common under-cabinet lighting mistakes

  • Mounting the lights at the back of the cabinet
  • Using bare LED strip over a polished countertop without a diffuser
  • Choosing a color temperature that does not match the ceiling lights
  • Undersizing the driver or installing it where it cannot be reached
  • Pairing a dimmer with an incompatible driver, causing flicker
  • Leaving gaps between fixtures so the counter has dark patches
  • Visible cords and connectors from a plug-in kit
  • Making lighting decisions after the backsplash is tiled

Adding lights to an existing kitchen

Light bars that plug into an existing receptacle are the usual retrofit and can be installed with basic tools. Linkable bars allow one cord to feed a whole run. A small cord cover painted to match the wall or cabinet makes the feed less noticeable.

A hardwired retrofit is possible when an electrician can bring power from a nearby receptacle or switch through the wall cavity. Whether this can be done without damaging the backsplash depends on the wall construction and on what is inside the wall.

Frequently asked questions

What type of under-cabinet lighting is best?

For most kitchens, LED strip in a diffused channel or linkable LED bars give the most even task light. Puck lights create separate pools of light and suit display or accent use more than food preparation.

Should under-cabinet lights be at the front or the back?

Toward the front of the cabinet bottom in most cases. That position lights the working part of the counter and keeps the fixture hidden behind the face frame or a light rail.

How bright should under-cabinet lighting be?

About 200 to 500 lumens per foot is a common range for task lighting. Choosing a dimmable system at the higher end allows the level to be adjusted to the countertop color and the time of day.

Does under-cabinet lighting need an electrician?

Plug-in kits generally do not. Hardwired fixtures, new switches and new outlets involve building wiring, which normally requires a licensed electrician and may require a permit, depending on local rules.

Can under-cabinet lights be dimmed?

Most LED under-cabinet systems can, if the fixture or driver is rated as dimmable and the dimmer is a compatible type. The manufacturer's list of tested dimmers is the most reliable guide.